How to: Install a touchscreen in your netbook

Tired of your netbook's tiny touchpad? Here's how to install a touchscreen.

Remove the metal RAM cover on the right. The captive screw should stay with that plate.

Remove the remaining hard-drive screw. Slide the drive to the left to unseat it from the SATA port. Remove the drive.

Within the keyboard cavity, remove the screw from the lower-left hole and the two screws on the lower edge on the right. The latter two sit on either side of the RAM. All of those screw holes are marked 'M2.5X5'.

Above the touchpad, remove the cable inside of the rectangular hole in the plastic. Gently lift up on the connector tab, again with a tool or fingernail, to release the cable.

Unplug the power-button cable at the top, middle of the case. Be careful to separate the cable plug from its socket. Instead of yanking on the wire, try to separate those two parts with tweezers or the dull edge of a hobby knife; they fit tightly.

Put the display at a 90-degree angle. Remove the black strip of plastic behind the display, above the battery housing. To do this, wedge guitar picks into the seam between the strip and the bottom housing. Point the picks down, along the inside of the bottom housing. Work around the edge to free the strip.

Starting from the gap you created, work guitar picks into the seam around the rest of the case, in front of the display. You'll likely need to leave some picks wedged in place as you work further, since the tight seam might clasp shut behind you. Remove that large, plastic part.

Install a Touchscreen in Your Netbook

On the display, use a hobby knife to pry off the rubber adhesive feet on the lower corners. Store those pads in the pillbox or somewhere else for later. Remove the two exposed screws.

Separate the front of the display housing from the back. Use guitar picks again, and gently work from the inside of the screen for better leverage. Avoid scraping the screen; lift the housing up slightly, and pry inside to release it.

Returning to the base of the laptop, near the front, remove the screw from the upper-left part of the Wi-Fi card. The card will pop out the way RAM does. It will still be attached to its two wires. Remove the card and set it to the left side of your workspace; loosen those wires from their tape and tabs as needed, but leave them attached.

Install a Touchscreen in Your Netbook

Remove the thick socket cable at the top-right side of the motherboard that leads to the display. Carefully separate it by pushing the edges with tweezers or another fine tip.

For this next step, you'll want to keep the display at 90 degrees, because you're going to remove the display and its connected housing now. Remove the three hinge screws that mount to the base, next to the motherboard. One is on the top-left side, in the general area of the VGA port, another is on the top-right side with an attached grounding loop wire, and the last is behind the display on the back-right corner.

Install a Touchscreen in Your Netbook

As you remove the screws, keep one hand propping up the display so that it doesn't fall. Once the display is free, set it behind the base of the laptop, as if you were opening it 180 degrees.

Remove the screw on the left of the base, generally near the USB ports. It's marked 'M2.5X5'. Remove the gray housing part that you just freed underneath.

Detach the flat, black ribbon cable from the lower left of the base by gently lifting and tilting the black tab in the socket. Use tweezers or other tools as needed. Lift the cable straight up.

Detach the cable connecting the main motherboard with the secondary circuit board on the left side of the base. This junction is next to the previous cable, and your target is the socket with the snarled, individual wires. Remove the screw underneath that cable.

Solder to the Netbook

Lift out the L-shaped board that holds the two USB ports, flash card slot, and VGA port. This is our target point to solder the touchscreen controller board cable to the laptop.

Join the Good Gear Guide newsletter!

Error: Please check your email address.

Tags notebookspc componentstouchscreensnetbooks

Our Back to Business guide highlights the best products for you to boost your productivity at home, on the road, at the office, or in the classroom.

Keep up with the latest tech news, reviews and previews by subscribing to the Good Gear Guide newsletter.

Zack Stern

PC World (US online)
Show Comments

Cool Tech

Crucial Ballistix Elite 32GB Kit (4 x 8GB) DDR4-3000 UDIMM

Learn more >

Gadgets & Things

Lexar® Professional 1000x microSDHC™/microSDXC™ UHS-II cards

Learn more >

Family Friendly

Lexar® JumpDrive® S57 USB 3.0 flash drive 

Learn more >

Stocking Stuffer

Plox Star Wars Death Star Levitating Bluetooth Speaker

Learn more >

Christmas Gift Guide

Click for more ›

Most Popular Reviews

Latest News Articles


GGG Evaluation Team

Kathy Cassidy


First impression on unpacking the Q702 test unit was the solid feel and clean, minimalist styling.

Anthony Grifoni


For work use, Microsoft Word and Excel programs pre-installed on the device are adequate for preparing short documents.

Steph Mundell


The Fujitsu LifeBook UH574 allowed for great mobility without being obnoxiously heavy or clunky. Its twelve hours of battery life did not disappoint.

Andrew Mitsi


The screen was particularly good. It is bright and visible from most angles, however heat is an issue, particularly around the Windows button on the front, and on the back where the battery housing is located.

Simon Harriott


My first impression after unboxing the Q702 is that it is a nice looking unit. Styling is somewhat minimalist but very effective. The tablet part, once detached, has a nice weight, and no buttons or switches are located in awkward or intrusive positions.

Featured Content

Latest Jobs

Don’t have an account? Sign up here

Don't have an account? Sign up now

Forgot password?